CORDLESS DRILL PABS 18 A1 CORDLESS DRILL Operation and Safety Notes Translation of original operation manual AKU ODVIJAC Upute za posluzivanje i za Vasu sigurnost Prijevod originalnih uputa za uporabu MAIN DE ÎNURUBAT CU ACUMULATOR Instruciuni de utilizare i de siguran Traducerea instruciunilor de utilizare originale AKKU-BOHRSCHRAUBER Bedienungs- und Sicherheitshinweise Originalbetriebsanleitung 7 Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device. Prije nego sto procitate tekst, otvorite stranicu sa slikama i upoznajte se na osnovu toga sa svim funkcijama ureaja. Înainte de a citi instruciunile, privii imaginile i familiarizai-v cu toate funciile aparatului. . , . Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen Funktionen des Gerätes vertraut. GB / CY HR RO BG GR / CY DE / AT / CH Operation and Safety Notes Upute za posluzivanje i za Vasu sigurnost Instruciuni de utilizare i de siguran Bedienungs- und Sicherheitshinweise Page Stranica Pagina Seite 5 15 25 37 49 61 1 2 3 4 9 8 5 6 7 A B C 7 D 11 12 10 Table of contents Introduction Intended purpose ..........................................................................................................Page Equipment Components ................................................................................................Page Scope of delivery ..........................................................................................................Page Technical Data ..............................................................................................................Page 6 6 7 7 General safety advice for electrical power tools ..................Page 7 1. Workplace safety .....................................................................................................Page 2. Electrical safety .........................................................................................................Page 3. Personal safety..........................................................................................................Page 4. Careful handling and use of electrical power tools ...............................................Page 5. Use and handling of the cordless electrical power tool ........................................Page Safety advice relating to cordless drill drivers ............................................................Page Attention - Service lines! ................................................................................................Page Original ancillaries / accessories .................................................................................Page 8 8 8 9 9 10 10 10 Before first use Charging the battery pack ...........................................................................................Page Insertion / removal of a battery pack into the appliance............................................Page Checking battery status ................................................................................................Page Changing tools ..............................................................................................................Page Torque pre-selection ......................................................................................................Page 2 Gear Drive .................................................................................................................Page 10 11 11 11 11 11 Preparing the tool for use Switching ON /OFF......................................................................................................Page Adjusting the speed ......................................................................................................Page Switching direction of rotation .....................................................................................Page Tips and Tricks ...............................................................................................................Page 12 12 12 12 Cleaning and Maintenance ........................................................................Page 13 Service .........................................................................................................................Page 13 Warranty ...................................................................................................................Page 13 Disposal ......................................................................................................................Page 14 Declaration of Conformity / Manufacturer..................................Page 14 GB/CY 5 Introduction The following pictograms are used in these operating instructions / on the device: Read instruction manual! Observe caution and safety notes! Caution ­ electric shock! Danger to life! Explosive material! Safety class II Drill chuck, Made In Germany Spindle lock Drill setting (torque preselect) Wear hearing protection, dust protection mask, protective glasses and protective gloves. Keep children away from electrical power tools! For indoor use only! Check that the device, mains lead and plug are in good condition! Dispose packaging and appliance in an environmentally-friendly way! Do not dispose of rechargeable batteries with your household refuse! © W Watts (Effective power) n0 V~ Ah Nm Design no-load speed Voltage Amp (Battery capacity) Newton metre (torque) DC (current and voltage type) Cordless drill PABS 18 A1 © Intended purpose Introduction Before you use it for the first time, it is essential that you make yourself fully familiar with the functions of the appliance and find out how to correctly handle electrically powered tools. To do this, read the following operating instructions carefully. Retain these instructions for future reference. Additionally, pass them on to whoever might acquire the appliance at a future date. This appliance is designed for drilling and screwing into wood, plastic and metal. Use the appliance only as described and only for the purposes indicated. Any other uses, and modifications to the appliance, are deemed to be improper usage and may result in serious physical injury. The manufacturer accepts no responsibility for damage(s) resulting from improper usage. The appliance is not intended for commercial use. © Equipment Components 1 Gear selector switch 2 Button - Battery condition / Battery display LED 3 Direction of rotation switch / lock 6 GB/CY Introduction / General safety advice for electrical power tools 4 5 6 7 8 9 10 11 12 ON / OFF Switch / R.P.M. regulator Bit storage Button for battery release Battery pack Torque pre-selector Drill chuck Fast charger Green charge-control LED Red charge-control LED Noise and vibration data: Measured values for noise are determined in accordance with EN 60745. The A-weighted noise level of the electrical power tool are typically: Sound pressure level: 66 dB(A) Sound power level: 77 dB(A) Uncertainty K: 3 dB Wear ear protection! © Scope of delivery Total vibration (vector sum of three directions) is calculated in accordance with EN 60745: Drilling in metal: Vibration emission value ah, D = 1.944 m / s2, uncertainty K = 1.5 m / s2, Vibration emission value ah = 2.101 m / s2, uncertainty K = 1.5 m / s2. 1 Cordless drill with rechargeable battery pack 1 Double bit 1 Fast charger 1 Carry case 1 Directions for use © Screwing: Technical Data PABS 18 A1 Cordless drill: Nominal voltage: 18 V DC Idle-running speed: 1st gear: max. 400 min-1 Idle-running speed: 2nd gear: max. 1300 min-1 Drill chuck clamping range: max. 10 mm Maximum drill diameter: Steel: 10 mm, Wood: 30 mm Max. torque: 20 Nm PABS 18 A1-1 Battery Pack: Nominal voltage: 18 V Capacity: 1.5 Ah Energy content: 27 Wh PABS 18 A1-2 Fast Battery Charger: INPUT Nominal voltage: 230 V~ 50 Hz Nominal output: 70 W OUTPUT Nominal voltage: Charging current Charging time: Protection class: WARNING! The vibration level given in these instructions has been measured in accordance with a standardised measurement procedure specified in EN 60745 and can be used to compare devices. Different uses of the device give rise to different vibration levels and in many cases they may exceed the values given in these instructions. It is easy to underestimate the vibration load if the electrical power tool is used regularly in particular circumstances. Note: If you wish to make an accurate assessment of the vibration loads experienced during a particular period of working, you should also take into account the intervening periods of time when the device is switched off or is running but is not actually in use. This can result in a much lower vibration load over the whole of the period of working. General safety advice for electrical power tools WARNING! Read all the safety advice and instructions! Failure to observe the safety advice and instructions may result in electric shock, fire and / or serious injury. GB/CY 7 18 V max. 2600 mA approx. 60 min II / General safety advice for electrical power tools Keep all the safety advice and instructions in a safe place for future reference! The term "electrical tool" used in the safety advice refers to electrical tools powered by mains electricity (by means of a mains lead) and electrical tools powered by rechargeable batteries (without a mains lead). device, to hang up the device or to pull the mains plug out of the mains socket. Keep the mains lead away from heat, oil, sharp edges or moving parts of the device. Damaged or tangled mains leads increase the risk of electric shock. e) When working outdoors with an electrical power tool always use extension cables that are also approved for use outdoors. The use of an extension cable suitable for outdoor use reduces the risk of electric shock. f) Use a residual current device (RCD) for protection if operating the electrical power tool in a moist environment is unavoidable. The use of an RCD reduces the risk of electric shock. 1. Workplace safety a) Keep your working area clean and well lit. Untidy or poorly lit working areas can lead to accidents. b) Do not work with the device in potentially explosive environments in which there are inflammable liquids, gases or dusts. Electrical power tools create sparks, which can ignite dusts or fumes. c) Keep children and other people away while you are operating the electrical tool. Distractions can cause you to lose control of the device. 3. Personal safety a) Remain alert at all times, watch what you are doing and always proceed with caution. Do not use the device if you are tired or under the influence of drugs, alcohol or medication. One moment of carelessness when using the device can lead to serious injury. b) Wear personal protective equipment and always wear safety glasses. The wearing of personal protective equipment such as dust masks, non-slip safety shoes, safety helmets or ear protectors, appropriate to the type of electrical power tool used and work undertaken, reduces the risk of injury. c) Avoid unintentional operation of the device. Check that the electrical power tool is switched off before you connect it to the mains, pick it up or carry it. Accidents can happen if you carry the device with your finger on the ON / OFF switch or with the device switched on. d) Remove any setting tools or spanners before you switch the device on. A tool or spanner left attached to a rotating part of a device can lead to injury. 2. Electrical safety a) The mains plug on the device must match the mains socket. The plug must not be modified in any way. Do not use an adapter plug with devices fitted with a protective earth. Unmodified plugs and matching sockets reduce the risk of electric shock. b) Avoid touching earthed surfaces such as pipes, radiators, ovens and refrigerators with any part of your body. There is an increased risk of electric shock if your body is earthed. c) Keep the device away from rain or moisture. Water entering an electrical device increases the risk of electric shock. d) Do not use the mains lead for any purpose for which it was not intended, e.g. to carry the 8 GB/CY General safety advice for electrical power tools e) Avoid placing your body in an unnatural position. Keep proper footing and balance at all times. By doing this you will be in a better position to control the device in unforeseen circumstances. f) Wear suitable clothing. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves clear of moving parts. Loose clothing, jewellery or long hair can become trapped in moving parts. g) If vacuum dust extraction and collection devices are fitted do not forget to check that they are properly connected and correctly used. The use of these devices reduces the hazard presented by dust. erly and move freely. Check for any parts that are broken or damaged enough ...