Satinelle Ice Premium HP6503/10 1 EnglisH 6 19 Cestina 5 eesti 8 Hrvatski 6 Magyar 75 88 Lietuviskai 10 HP6503/10 6 EnglisH introduction With your new Satinelle ICE PREMIUM you can remove unwanted hairs quickly, easily and effectively. The combination of the ceramic epilating system with the contour-following skin cooler and the new sonic massaging system constitutes a revolution in epilation. Thanks to the natural numbing effect of ice and massaging, the new Satinelle ICE PREMIUM makes epilation more comfortable and less painful than ever. The result is a silky-smooth skin and a hair growth reduction of up to 50%, assuming you use the appliance regularly (every 4 weeks). The Satinelle ICE PREMIUM is suitable for all body parts and comes with a skin cooler that has been specially developed for epilating sensitive areas (underarms, bikini line). These areas can be particularly sensitive to pain, which this special skin cooler helps to diminish. The rapidly rotating epilating discs catch even the shortest hairs (down to 0.5 millimetre!) and pull them out by the roots. As a result, your skin stays smooth for up to four weeks and regrowth is soft and downy. general description (Fig. 1) A B C D E F G H I J K L Insulating sleeve for skin cooler Leg skin cooler with pivoting cooling head Skin cooler for underarms and bikini line Shaving head Protective cap of shaving head Massaging element Epilating head Appliance Charging light Adapter Cleaning brush Exfoliating body puff important Read this user manual carefully before you use the appliance and save it for future reference. EnglisH , , , , , , , , , , , , , 7 Check if the voltage indicated on the adapter corresponds to the local mains voltage before you connect the appliance. Only use the appliance in combination with the adapter supplied. Do not use the appliance if the adapter or the appliance itself is damaged. If the adapter is damaged, always have it replaced with one of the original type in order to avoid a hazard. The adapter contains a transformer. Do not cut off the adapter to replace it with another plug, as this causes a hazardous situation. Keep the appliance and the adapter dry. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. Do not expose the appliance to temperatures lower than 5°C or higher than 5°C. To prevent damage and injuries, keep the running appliance away from your scalp hair, eyebrows, eyelashes, clothes, threads, cords, brushes etc. This appliance contains two NiMh rechargeable batteries that may harm the environment if not disposed of properly. Do not use the appliance on irritated skin or skin with varicose veins, rashes, spots, moles (with hairs) or wounds without consulting your doctor first. People with a reduced immune response or people who suffer from diabetes mellitus, Raynaud's disease or immunodeficiency should contact their doctor first. Noise level: Lc = 75.8dB [A] electromagnetic fields This Philips appliance complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user manual, the appliance is safe to use based on scientific evidence available today. 8 EnglisH Charging You can run the appliance directly from the mains or you can use it without the cord when the batteries have been charged. Charge the batteries at least 16 hours before you use the appliance for a cordless operating time of up to 20 minutes. Do not charge the appliance for more than hours. 1 Make sure the appliance is switched off while charging. Insert the appliance plug into the bottom of the appliance and put the adapter in the wall socket. , The charging light goes on and stays on to indicate that the appliance is charging. The charging light does not go out or change colour when the appliance is fully charged. Optimising the lifetime of the batteries After you have charged the appliance for the first time, do not recharge it between epilating or shaving sessions. Continue to use it and only recharge it when the battery is (almost) empty. Discharge the batteries completely twice a year by letting the motor run until it stops. Do not keep the appliance plugged into a wall socket all the time. If the appliance has not been used for a long time, it must be recharged for 16 hours. Preparing for use Freezing the skin cooler 1 Put the skin cooler WITHOUT the insulating sleeve in the freezer or freezing compartment (***) at least hours before you start to epilate. When the fluid has turned completely blue, the skin cooler is ready for use. Make sure the outside of the skin cooler is completely dry before you freeze it. EnglisH Tip:You can store the skin cooler in the freezer permanently. using the appliance general information about epilation , , , , , 9 , Epilation is easier just after a bath or shower. Make sure your skin is completely dry when you start to epilate. When you use the appliance for the first time, we advise you to try it out on an area with only light hair growth. This helps you get accustomed to the epilation process. For optimal epilating results, the hairs should not be longer than 10 millimetres (Fig. ) To epilate longer hairs: (Fig. ) shorten the hairs to a maximum length of 10mm with a trimmer. In this case, you can start to epilate right away. shave the hairs completely. In this case you can start to epilate after a few days (the hairs must be at least 0.5mm long). Your skin may become a little red and irritated the first few times you use the epilator. This phenomenon is absolutely normal and quickly disappears. As you use the appliance more often, your skin gets used to epilation, skin irritation decreases and regrowth becomes thinner and softer. If the irritation has not disappeared within three days, we advise you to consult a doctor. We advise you to epilate before you go to bed at night, as this allows any skin irritation that may develop to diminish overnight. Corded use Do not run the appliance from the mains when the battery is fully charged. 1 To run the appliance from the mains, switch off the appliance and connect it to the mains. Wait a few seconds before you switch on the appliance. 10 EnglisH Epilating with the leg skin cooler Make sure your skin is clean, entirely dry and free from grease. Do not use any cream before you start to epilate. 1 Slide the insulating sleeve onto the skin cooler. (Fig. ) The insulating sleeve prevents an unpleasant sensation of coldness in your hand while you use the appliance. It also keeps the skin cooler cold as long as possible. Sometimes the pivoting cooling head freezes onto the skin cooler and does not move when you take the skin cooler from the freezer. The pivoting cooling head starts to pivot again after you have passed it over your leg a few times. Snap the appliance onto the skin cooler (Fig. ). Insert the appliance plug into the bottom of the appliance and put the adapter in the wall socket. Select the desired speed to switch on the appliance (Fig. 5). Select speed I for areas with little hair growth and for areas where bones are located directly beneath the skin, such as knees and ankles. Select speed II for larger areas with stronger hair growth. 5 Stretch your skin with your free hand to make the hairs stand upright. 6 Place the appliance perpendicularly onto the skin with the epilating head pointing forward. Move the appliance against the direction of hair growth at a moderate speed. (Fig. 6) Make sure both the epilating discs and the skin cooler are in proper contact with the skin. Press the appliance lightly onto the skin. , If you are not completely satisfied with the epilation result, try moving the epilator more slowly over your skin. 7 Use the tab on the bottom end of the appliance to remove the appliance from the skin cooler (Fig. 7). EnglisH 11 Epilating with the skin cooler for underarms and bikini line The special skin cooler for the underarms and the bikini line reduces the number of active epilating discs. Combined with the large cooling surface, this skin cooler makes epilating sensitive areas less painful. You get the best results when the hairs are not too long (max. 1cm). 1 Slide the insulating sleeve onto the skin cooler. (Fig. 8) Snap the appliance onto the skin cooler (Fig. 9). Switch on the appliance by selecting the desired speed. (Fig. 5) We advise you to use speed I. To epilate the underarm area, place one arm behind your head to stretch the skin. Then place the appliance perpendicularly onto the skin with the hand of the other arm (Fig. 10). 5 To epilate the bikini line, stretch the skin with your free hand and place the appliance perpendicularly onto your skin. Do not exert any pressure (Fig. 11). 6 Move the appliance slowly across the skin against the direction of hair growth. 7 Use the tab on the bottom end of the appliance to remove the appliance from the skin cooler for underarms and bikini line (Fig. 1). Epilating without skin cooler , , If you do not want to use the skin cooler, for instance because you have grown accustomed to the sensation of epilation, you can also use the appliance without the skin cooler. Make sure that you place the epilator perpendicularly onto your skin and that you move it against the direction of hair growth. using the exfoliating body puff Use the exfoliating body puff in the shower. Regular massages with the puff may help to prevent ingrown hairs. Do not use the puff immediately before or after epilation. 1 EnglisH shaving You can use the shaving head to shave sensitive body parts, such as your underarms and bikini line. With the shaving head, you obtain a smooth result in a comfortable and gentle way. 1 Make sure the appliance is switched off. Remove the skin cooler (Fig. 7). Remove the epilating head (Fig. 1). Press the release button (1) and move the epilating head in the direction of the arrow (2). Place the shaving head on the appliance and press it onto the appliance until it snaps home (`click') (Fig. 1). 5 Switch on the appliance by selecting speed II. 6 Place the shaving head onto your skin and move the appliance slowly and smoothly against the direction of hair growth. Press the appliance lightly (Fig. 15). Cleaning and maintenance Never rinse the adapter or the appliance itself with water. Do not use any corrosive detergents, scouring pads or cloths, petrol, acetone etc. to clean the appliance. 1 Make sure the appliance is switched off and unplugged. Remove the skin cooler from the appliance and slide the insulating sleeve off the skin cooler. Clean the pivoting cooling head of the leg skin cooler with the brush supplied or with a moist cloth after each use. Make sure the outside of the skin cooler is completely dry before you freeze it again. Cleaning the epilating head Clean the epilating head after every use. EnglisH 1 1 Make sure the appliance is switched off and unplugged. Remove the epilating head (Fig. 1). Press the release button (1) and move the epilating head in the direction of the arrow (2). Remove the massaging element (Fig. 16). Clean all accessible parts, including the bottom of the epilating head and the epilating discs, with the brush (Fig. 17). 5 You can also rinse the epilating head (not the appliance!) under the tap to clean it more thoroughly (Fig. 18). Never try to detach the epilating discs from the epilating head. 6 Reattach the massaging element to the epilating head. Then place the epilating head on the appliance and press it until it snaps home (`click') (Fig. 19). The epilating head only fits onto the appliance in one way. Cleaning the shaving head Clean the shaving head after every use. 1 Make sure the appliance is switched off and unplugged. Remove the shaving head. Pull the cutter unit out of the shaving head. (Fig. 0) Brush the hairs off the cutter unit and the shaving head. Make sure that you also brush away any hairs that have collected under the trimmers (Fig. 1). 5 You can also rinse the cutter unit and the rest of the shaving head (not the appliance!) under the tap (Fig. ). 6 Put the cutter unit back into the shaving head and snap the shaving head back onto the appliance (`click') (Fig. ). Do not exert pressure on the shaving foil to avoid damage. 7 Rub a drop of sewing machine oil onto the trimmers and shaving foil of the shaving unit twice a year. 1 EnglisH storage 1 Put the protective cap on the shaving head (`click'). (Fig. ) Store the appliance and the accessories in the pouch. Replacement If you use the shaving head several times a week, replace the cutter unit (type HP6193) after one or two years of use or if it is damaged. Environment Do not throw away t ...